How to Replace a Bathtub Yourself: Removing and also Replacing.
How to Replace a Bathtub Yourself: Removing and also Replacing.
Blog Article
On this page in the next paragraph you can find additional professional help and advice in regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
Setting up a tub isn't exactly rocket science, yet it does call for strong plumbing, carpentry, and sometimes, tiling abilities. Changing an old tub with a new one is additionally a reasonably tough project. If the old tub is conveniently easily accessible, the job can move speedily; if you need to open up a wall to remove the old bathtub as well as position the new bath tub, the task is much harder. In either instance, the job is within a house handyman's skills, although you will certainly need a helper to vacate the old bathtub and embeded in the brand-new one. Ensure you have actually certified yourself for the work as well as are comfortable trying it. Instead of hiring a contractor to take control of a halfway-completed job, it is far better to take into consideration utilizing one prior to you start. Chances are you might need a specialist plumber to make tube connections.
This article will help you set up a new bath tub in your restroom if you have actually already acquired a brand-new tub as well as don't require to change the setup of your previous supply of water pipelines.
Your tools and also material list ought to consist of the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you need to do is disconnect the water system. After doing so, turn on the faucets to drain pipes any type of water continuing to be in the system. The process of getting rid of the existing taps can be rather bothersome due to the limited access that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a towel ready for the staying water that will certainly come from the pipes. As soon as the supply pipes have been gotten rid of, use the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming throughout this process. When the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned of any old securing substance.
Prior to proceeding to fit the new taps, contrast the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic adapter to stop damage to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end gives a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin making certain that the washing machines are in place between the tap and the sink. Secure the tap in place with the producer supplied backnut. When the tap is securely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical tap connectors. The former kind needs to be attached to the faucet ends first, tightening just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Tub
Using the two wood boards under its feet, put the tub in the required position. The wood boards are practical in uniformly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto four tiny factors.
The next goal is to make certain that the bath tub is leveled all round. This can be accomplished by checking the level as well as changing the feet on the bathtub till the level reads degree.
To set up taps, fit all-time low of the outermost versatile tap adapter to the suitable supply pipe by making a compression sign up with; then do the same for the various other tap.
Switch on the water system as well as check all joints and also new pipework for leakages as well as tighten them if necessary. Load the tub and likewise check the overflow electrical outlet as well as the normal electrical outlet for leaks.
Ultimately, repair the bathroom paneling as explained in the manufacturer's instruction manual. Tiling and also securing around the bathtub should wait till the tub has actually been utilized at least when as this will certainly settle it right into its final position.
Planning for the Installation
To start with, the sustaining frame provided with the bath needs to be fitted (if needed) according to the maker's instructions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to see to it that if the faucet comes with a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets device to prevent pressure on the bathtub.
Fit the flexible tap adapters to the bottom of the two faucets utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom need to now be ready to be suited its final position.
Tiling Around the Tub
In the location where the bath satisfies the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to fracture a rigid seal, causing the water to permeate the wall surface in between the bath as well as the tiling, causing difficulties with dampness and also possible leaks to the ceiling below.
You can select from a selection of coloured sealers to blend in your fixtures as well as installations. They are marketed in tubes and also cartridges, and are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly load the bath tub with water prior to securing, to allow for the movement experienced when the tub is in use. The sealant can break relatively very early if you do not think about this motion prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water-proof glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate more info about How to Install a Bathtub? Create feedback down the page. We would be interested to hear your views about this entry. We are looking forward that you come back again later on. Be sure to set aside a second to share this post if you appreciated it. We take joy in reading our article about How to Install a Bathtub Yourself.
Article Report this page